The purpose of this study is to develop and validate a numerical tool for evaluating the performance of a settling basin regarding the trapping of suspended matter. The Euler-Lagrange approach was chosen to model the flow and sediment transport. The numerical model developed relies on the open source library OpenFOAM®, enhanced with new particle/wall interaction conditions to limit sediment deposition in zones with favourable hydrodynamic conditions (shear stress, turbulent kinetic energy). In particular, a new relation is proposed for calculating the turbulent kinetic energy threshold as a function of the properties of each particle (diameter and density). The numerical model is compared to three experimental datasets taken from the literature and collected for scale models of basins. The comparison of the numerical and experimental results permits concluding on the model's capacity to predict the trapping of particles in a settling basin with an absolute error in the region of 5% when the sediment depositions occur over the entire bed. In the case of sediment depositions localised in preferential zones, their distribution is reproduced well by the model and trapping efficiency is evaluated with an absolute error in the region of 10% (excluding cases of particles with very low density).
Runoff water transported in drainage networks can carry substances harmful for aquatic environments (organic matter, metals, fuels, etc.). A fraction of this pollution is fixed on suspended matter (SM) (Ashley et al. 2004). To limit pollution discharged in the receiving medium, different systems have been installed at the outlets of networks with the overall objective of trapping SM by settling. The size of these structures can vary from several cubic metres, for lamella and dynamic settlers, to several tens of thousand cubic metres for storage basins. Despite the intensive use of these systems, often little is known of how they function and their settling efficiency is estimated using dimensioning rules based on Hazen's sedimentation theory (Jarrell-Smith & Friedrich 2011). However, the flow can have very different forms according to the geometry of the structure considered: horizontal or vertical, and symmetrical or asymmetrical recirculations (Dewals et al. 2008; Dufresne et al. 2009). In this case, Hazen's sedimentation theory can prove to be uncertain, as it is used outside its scope of application, and another method must be used to evaluate the efficiency of the structure more precisely.
Several solutions are available. An evaluation can be performed on site by instrumenting the installation to measure turbidity and by taking samples at the inlet and outlet of the system, for example (Torres 2008). Nonetheless, this evaluation can only be done once the structure has been built, and its implementation is poorly adapted to the dimensioning phase. It is also possible to study the operation of a settling basin in the laboratory (Adamsson et al. 2005). However, setting up this type of system can be expensive and is limited to small structures and scale models. On the contrary, experimental data collected on site or in the laboratory are essential for validating 3D numerical models, another solution for evaluating the operation of a structure at lower cost. Consequently, this article focuses on the development and validation of a methodology based on numerical modelling to predict the performances of a settling basin for design purposes.
The movement of a number of solid particles in a fluid can be modelled by two methods: the Euler-Euler approach and the Euler-Lagrange approach. In the Euler-Euler approach, the fluid phase and the particle phase are considered as continuous phases and are modelled with Navier-Stokes equations. In the case of the Euler-Lagrange approach, the Navier-Stokes equations are still resolved for the fluid phase and Newton's equation of movement is used to determine the trajectory of each particle within the flow (Maxey & Riley 1983). Since the concentration of SM in runoff water is mostly lower than 1 g/l (Ashley et al. 2004), the particle phase does not influence the flow and the hydrodynamic calculation can be uncoupled from the movement of particles (Graf & Altinakar 2000). The uncoupled Euler-Lagrange approach was employed successfully in several studies to reproduce particle trapping efficiency in a basin and the distribution of sediment depositions on the bottom (Adamsson et al. 2003; Dufresne et al. 2009; Yan et al. 2014). This approach is used in the present study.
The Euler-Lagrange approach
Hydrodynamic modelling in basins is well mastered. A RANS approach (Versteeg & Malalasekera 2007) coupled with a k-ɛ type turbulence model and its variants suffices to reproduce the diversity of the types of flows occurring in basins (Stovin & Saul 1996; Dufresne et al. 2010). Regarding the modelling of sediment transport, calculating the trajectory of a particle, knowing the forces exerted on it (Maxey & Riley 1983), is also well mastered (Adamsson et al. 2003; Dufresne et al. 2009; Yan et al. 2014). The main difficulty relating to this type of model resides in the boundary condition used to take into account the deposition and the resuspension of a particle that has reached the bottom wall.
The simplest interaction conditions are stick and rebound conditions (OpenFOAM 2016). For a stick type condition, a null velocity is fixed for the particle coming into contact with the wall and the calculation of its trajectory stops. For a rebound type condition, the particle is resuspended in the flow using an elastic collision equation. These conditions can nonetheless prove to be poorly adapted for representing sediment depositions on the bottom of a basin. Indeed, no sediment deposition is possible with a rebound condition, whereas using a stick condition can lead to an overestimation of deposits since any particle reaching the bottom remains deposited (Stovin & Saul 1998). New conditions were therefore proposed to limit sediment depositions to zones with favourable hydrodynamic conditions. All these conditions are based on the same idea of comparing a local hydrodynamic parameter with a threshold value.
Adamsson et al. (2003) used shear stress on the bed as a hydrodynamic parameter (BSS for Bed Shear Stress condition). The threshold value selected was evaluated at about 0.03 N/m2 by Stovin & Saul (1994) on the basis of experiments on a scale model of a basin. The use of this BSS condition led to major improvements in terms of representing zones of sediment deposition in comparison to a stick condition. It should nonetheless be noted that the threshold value used is only valid a priori for the scale model and the particles studied experimentally by Stovin & Saul (1994) and numerically by Adamsson et al. (2003).
Another approach was proposed by Dufresne et al. (2009). It is based on thresholding the turbulent kinetic energy close to the bed (BTKE for Bed Turbulent Kinetic Energy condition). Based on experiments conducted on a small scale laboratory model, the authors identified the range 1.10−4–3.10−4 m2/s2 for the threshold value of turbulent kinetic energy. The sediment depositions simulated with the BTKE condition showed good consistency with the sediment depositions observed, and provided a better description in comparison to a BSS condition. Yan et al. (2014) applied a BTKE condition to reproduce sediment depositions in a large structure (32,000 m3). The authors determined a threshold value around 10 times lower than that highlighted by Dufresne et al. (2009), Yan et al. (2014), then proposed the relation kc = ξvs2 to determine the critical turbulent kinetic energy, with ξ being the adjustment coefficient and vs being the settling velocity representative of the sample. The authors obtained highly satisfactory results by considering a coefficient ξ equal to 1 and a settling velocity vs,80 (percentile 80 of the distribution of settling velocities).
For both the BSS and BTKE conditions, the threshold values proposed were adjusted experimentally for a given basin and a sample of particles, making it difficult to transpose them to other configurations. Therefore it would be interesting to obtain a relation that permits the calculation of the threshold value associated with each particle as a function of its properties (diameter and density).
Analogy with channels
Finally, the idea chosen in the present study is to use the formulations obtained in channels as the basis for creating new conditions of interaction between the particles and the bottom walls that are adapted to cases of basins. The aim is to develop a numerical model based on the Euler-Lagrange approach, enriched with new conditions of interaction of BSS and BTKE type using the properties of the particles. The model is then compared to experimental data obtained from the literature to identify the most pertinent condition for reproducing particle trapping efficiency in a basin and the location of sediment deposits on the bottom.
MATERIALS AND METHOD
The movement of the fluid is described by Navier-Stokes equations (Versteeg & Malalasekera 2007). For an incompressible fluid, these equations are expressed by a mass conservation equation and a momentum conservation equation. Water and air flows are described using the Volume of Fluid method (Hirt & Nichols 1981) by considering only one fluid whose properties (density and viscosity) vary linearly with the volume fraction α. This parameter is a marker of value 1 in the water phase and 0 in the air phase. It is calculated by resolving a transport equation (Rusche 2002).
The flows considered in this study are turbulent. The Navier-Stokes equations are averaged with time by applying a Reynolds decomposition for the instantaneous velocity and pressure (Versteeg & Malalasekera 2007), and a turbulence model is used to describe the effect of the velocities fluctuating over the mean flow. The k-ω SST model (Shear Stress Transport) with a standard wall function is chosen. The resolution of these equations is done using the interFoam solver (Rusche 2002), available in the library OpenFOAM® (OpenFOAM 2016). A full description of this solver is provided in Deshpande et al. (2012).
The apparent weight of a particle Fg corresponds to the force due to the reduced gravity of buoyancy linked to the surrounding fluid. It is expressed by Fg = mpg (1– ρ/ρp) where g = the gravity acceleration. The additional forces Fa are not detailed here as they are not taken into account in what follows due to their negligible impact on the trajectory (Dufresne et al. 2009).
The velocity of the fluid u in Equation (6) corresponds to the instantaneous velocity, whereas the result of a hydrodynamic simulation using the RANS method provides an average velocity U. Using the mean velocity to calculate the trajectories amounts to neglecting the turbulent nature of the flow. However, turbulence has the effect of diverting the particles from their trajectories and even of trapping them in eddies for a certain period of time. These phenomena are therefore not negligible. Following the use of a RANS model, the turbulent nature of the flow can be taken into account by using a random walk model to model the turbulent dispersion of particles. Eddies are created randomly and affect the trajectory of the particles. In practice, a local fluctuation component u’ is added to the mean velocity of the fluid U at the point where the particle is located. The velocity used to calculate the trajectories is therefore u = U + u’. The fluctuating component is estimated by |u’| = φ (2k/3)0.5 where φ is the random number generated from a Gaussian distribution of mean 0 and variance 1; and (2k/3)0.5 is the quadratic mean of the fluctuations of the fluid velocity for an isotropic turbulence. The direction of the fluctuating velocity is also generated randomly. The algorithm used is available in the sources (OpenFOAM 2016).
The fluctuating value u’ is recalculated at every time step of the correlation tturb and is maintained constant otherwise. The correlation time is calculated using the model proposed by Amsden et al. (1989) by tturb = min (1/ω; cps k0.5/(ω |U + u’ – up|)) where k and ω are the turbulent variables of the model k-ω SST; and cps is the empirical constant, equal to 0.16432. The first term in the parenthesis corresponds to the lifetime of the eddy and the second represents the time required for the particle to cross the eddy.
New particle/wall interaction conditions
The BSS and BTKE type conditions are pertinent for modelling the behaviour of the particles close to the bottom of the basin. The threshold values to be selected are, on the other hand, still subject to debate (Adamsson et al. 2003; Dufresne et al. 2009; Yan et al. 2014). A new method, on the scale of the particle, is proposed to calculate the threshold values τc (for the BSS condition) and kc (for the BTKE condition). They are calculated for each particle as a function of their physical properties, such as diameter, density and settling velocity.
The BSS condition is based on the comparison of the shear stress at the wall with a threshold stress τc. The threshold value is calculated for each particle as a function of its dimensionless diameter d* (Equation (3)) by using the interpolation of the Shields diagram proposed by Brownlie (1981) (Equation (1)). This condition is called ‘Brownlie BSS’ in the rest of the paper.
Extension of the Van Rijn criterion. Using the Van Rijn (1984b) criterion, parameter ξ is not defined for the d* < 1. Two possibilities will be investigated for the extension. The first consists of conserving Equation (11) for the d* < 1. This condition will be called ‘Van Rijn BTKE’ in the rest of the paper. The second is based on the estimation of the value of ξ using the Shields diagram (Equation (1)) and Equations (9) and (10). The settling velocity ws is calculated using the Stokes formula (Jarrell-Smith & Friedrich 2011), which is valid for the particles considered here (d* < 2). The choice of using the Shields diagram for d* < 2 is justified, since the criteria that characterise the start of bed load and suspension are confounded for this range of d* (Van Rijn 1984b). Curve ξ = 320/d*4 provides an acceptable approximation for the d* between 0.1 and 2.5. To ensure the continuity in the calculation of ξ, the following relations are proposed: ξ = 320/d*4 for 0.1 < d* < 2, ξ = 80/d*2 for 2 < d* < 10, and ξ = 0.8 for d* > 10. This condition will be called ‘extended Van Rijn BTKE’ in the rest of the paper.
The methodology is applied to three series of experiments performed on scale models of basins by Frey et al. (1993), Stovin & Saul (1994) and Dufresne et al. (2009). The comparison of the numerical results with the experimental measurements makes it possible to verify the model's capacity to reproduce the phenomena involved in the sediment transport in the basin on the basis of two data: particle trapping efficiency in the structure and the preferential zones of sediment deposition on the bottom. The three series of experiments present the characteristics that allow applying the model to a wide range of particles and hydraulic configurations. The parameters of the experiments are summarised in Table 1. These experiments correspond to calmed though nonetheless turbulent flows.
|Experiments .||Frey et al. (1993) .||Stovin & Saul (1994) .||Dufresne et al. (2009) .|
|d*50||1.3; 1.5; 1.8; 2.1; 2.5||0.77||5.12|
|Sediment deposits||Over the whole bed||In localised zones||In localised zones|
|Experiments .||Frey et al. (1993) .||Stovin & Saul (1994) .||Dufresne et al. (2009) .|
|d*50||1.3; 1.5; 1.8; 2.1; 2.5||0.77||5.12|
|Sediment deposits||Over the whole bed||In localised zones||In localised zones|
The experiments performed by Frey et al. (1993) led to validating the model for hydraulic conditions in which sediment deposit could occur over the whole bed of the structure. The main aim is therefore to verify the model's capacity to reproduce the structure's particle trapping efficiency. In the experiments performed by Stovin & Saul (1994), the hydrodynamic conditions were such that zones without any sediment deposits appeared on the bottom of the basin. The sample of particles used covered a d* between 0.15 and 2.5, thus, in addition to the trapping efficiency, these experiments are well-adapted to study the new particle/wall interaction conditions, in particular the extension of the Van Rijn (1984b) criterion for small d* (d* < 2). In the experiments of Dufresne et al. (2009), the dimensionless diameters d* of the particles used were between 2.5 and 10. As with the experiments of Stovin & Saul (1994), the hydrodynamic conditions in the basin were such that sediment depositions were not possible in certain zones. These experiments therefore permit studying the pertinence of the particle/wall interaction conditions for the largest d* (d* > 2).
The experiments of Frey et al. (1993)
Numerical modelling of the flow and sediment transport. The seven geometric and hydraulic combinations were simulated numerically using the interFoam solver presented previously. The four geometries were meshed using the snappyHexMesh tool (OpenFOAM 2016). ‘Cut-cell’ type meshes with sides of about 7.5 mm and a height of 2.5 mm were chosen (i.e. a y+ of the order from 1 to 3), leading to a computational domain composed of 500,000 to 600,000 cells according to the geometry. The velocity was imposed on the inlet face of the structure to reproduce the discharges injected experimentally. The boundary condition at the outlet and on the upper part of the computational domain was an atmospheric pressure. The turbulence model k-ω SST was used with standard wall laws (Versteeg & Malalasekera 2007; OpenFOAM 2016). The convergence of the calculation was checked on the basis of stability with time of the mass balance at the outlet and the field of velocities in the different longitudinal and transversal planes.
The particle tracking model presented above was applied to the seven geometric and hydraulic combinations. For each sand sample, a Rosin–Rammler distribution was interpolated to reproduce the experimental grain size distribution. After having verified that this number was sufficient to obtain statistically representative results, 10,000 particles with a density of 2,650 kg/m3 were injected into the hydraulic flow. In order to reproduce the injection method used experimentally by Frey et al. (1993), the injection surface was defined by a disc 8 mm in diameter placed immediately upstream of the break of slope. The centre of the disc was centred in relation to the side walls and located 10 mm from the bottom of the supply channel. The forces taken into account to calculate the trajectories of the particles were drag force and apparent weight. The turbulent nature of the flow was modelled using the stochastic dispersion model presented previously. A rebound condition was used for the inlet and the side walls. An escape condition (OpenFOAM 2016) was applied to the outlet and to the atmosphere. Regarding the bottom of the structure, using the stick condition was, a priori, sufficient since, on the one hand, the sediment depositions observed experimentally were not localised in certain zones of the bottom (Frey et al. 1993), and on the other hand, the authors showed that by covering the bottom of the settling basin with particles and by progressively bringing the discharge to its nominal value, the particles did not return to suspended state (no particle collected at the outlet of the structure). The new particle/wall interaction conditions (BSS and BTKE) were, however, used to determine whether one of them permitted obtaining more consistent results than with the stick condition or, failing that, verifying that they provided similar results. The boundary conditions used were therefore: stick, ‘Brownlie BSS’, ‘Van Rijn BTKE’, ‘extended Van Rijn BTKE’ and a BTKE condition with a fixed coefficient ξ. For the latter condition, the values ξ = 1 (Yan et al. 2014) and ξ = 5 (Bagnold criterion) were studied.
The experiments of Stovin & Saul (1994)
Numeric modelling of the flow and sediment transport. The methodology followed to model the flow and sediment transport is analogous to that presented for modelling the experiments of Frey et al. (1993). All the details can be found in Isenmann (2016). For the bottom of the structure, the particle/wall interaction conditions investigated are: stick, ‘Brownlie BSS’, ‘Van Rijn BTKE’, and ‘extended Van Rijn BTKE’. The BTKE conditions with a fixed value of ξ were not used, since a preliminary study of the distribution of the turbulent kinetic energy on the bottom showed that no particle could be deposited given the threshold calculated (Isenmann 2016).
The experiments of Dufresne et al. (2009)
Experimental protocol and experimental results. The experiments conducted by Dufresne et al. (2009) were performed on a scale model of a rectangular basin. Two configurations were studied: an outlet by a culvert in the lower part of the basin and an outlet by an overflow. The shape and dimensions of the structure are described in Dufresne et al. (2009). A range of discharges between 1 and 5 l/s was investigated for different water depths between 8 and 40 cm. The particles injected were white polystyrene beads with a grain size ranging from 350 to 1,400 μm with a median diameter of 738 μm (d* between 2.5 and 10). The density was evaluated at 1,034 kg/m3 (±19 kg/m3) by pycnometry. At the end of the experiment, the particles settled and recovered at the outlet were reintroduced in a measurement column to evaluate the structure's efficiency. Furthermore, photographs and films of the bottom of the basin were taken for each experiment to track the evolution of the sediment depositions.
Numeric modelling of the flow and sediment transport. The methodology followed to model the flow and sediment transport was analogous with that presented for modelling the experiments of Frey et al. (1993) and Stovin & Saul (1994). All the details can be found in Isenmann (2016). The particle/wall interaction conditions studied were: stick, ‘Brownlie BSS’, ‘Van Rijn BTKE’ and BTKE with a fixed value of ξ (equal to 1 and 5). It should be noted that the ‘extended Van Rijn BTKE’ condition was equivalent to the ‘Van Rijn BTKE’ condition for the range of d* associated with these experiments (d*min > 2). Due to the large standard deviation on the value of the density of the particles in relation to the density of the water (1,034 ± 19 kg/m3), two other values were also investigated: 1,015 kg/m3 (corresponding to the low value of the range) and 1,025 kg/m3 (corresponding to the intermediate value between the average value and the low value).
RESULTS AND DISCUSSION
Comparison of numerical and experimental results
The experiments of Frey et al. (1993)
When all the particles had been deposited or had left the structure via the outlet, the mass percent at the outlet could be calculated. Figure 1 shows the comparison between the numerical and experimental results for the 34 simulations performed under the stick condition. Each graph corresponds to a geometrical and hydraulic configuration for the different sand samples studied. The samples are represented by their median dimensionless diameter d*50. The absolute variance between the calculated value and that measured experimentally is on average ±6% of the efficiency. The variance is larger for low values of d*, with a maximum of 17%. Generally, the numerical model faithfully reproduces particle trapping efficiency in the structure, as most of the values were within the experimental error bars. The numerical results obtained for the other particle/wall interaction conditions are not described here, but are available in Isenmann (2016). Nonetheless, it should be emphasised that the ‘Brownlie BSS’, ‘Van Rijn BTKE’ and ‘extended Van Rijn BTKE’ conditions provide similar results to the stick condition and are thus well adapted for this case where the sediment deposits cover the whole of the bottom. However, the BTKE conditions using a fixed value of ξ (equal to 1 or 5) appear to be too restrictive regarding the sediment deposition (presence of zones free of sediment) and thus lead to underestimated trapping efficiencies most of the time.
The experiments of Stovin & Saul (1994)
At the end of the simulation, the basin's trapping efficiency was calculated for each of the boundary conditions investigated for the bottom of the structure. Figure 2 shows the comparison of the numerical and experimental efficiencies as a function of the supply discharge for water depths of 0.20 m and 0.30 m. Since the experimental measurements could present a wide range of efficiencies for the same discharge (for example, between 8% and 27% at 11.5 l/s for a water depth of 0.20 m in Figure 2), the variances were calculated in relation to the mean value of the three experimental measurements (represented by a cross in Figure 2).
The results for the trapping efficiency show high sensitivity to the interaction condition used. The stick condition leads to an overestimation of efficiency in the region of 20–35% in most cases, except for low discharges. Trapping efficiency was also overestimated with the ‘Brownlie BSS’ condition, with however a smaller variance with the experimental measurements (about 10–20%). On the contrary, the ‘Van Rijn BTKE’ condition led to an underestimation of trapping efficiency for all the experiments. The differences with the measurements could reach 30% (low discharge and water depth of 0.30 m). Lastly, the ‘extended Van Rijn BTKE’ condition supplied trapping efficiencies that were sometimes higher and sometimes lower than the experimental measurements, with the variance always lower than 10%, except for the lowest discharge (15%).
The other essential point for determining the most efficient interaction condition concerns the location of the sediment deposits at the bottom of the structure. The sediment depositions at the end of the simulation are presented in Figure 3 for each interaction condition, and are compared with the sediment depositions observed by Stovin & Saul (1994). The comparisons are made for the three experiments for which the sediment depositions observed experimentally are available, that is to say, those observed for a water depth of 0.20 m and discharges of 4.28, 10.23 and 16.03 l/s.
The sediment depositions obtained with the stick and ‘Van Rijn BTKE’ conditions confirm the weakness of these conditions, already highlighted when comparing the trapping efficiencies. Indeed, the stick condition leads to sediment depositions over the entire bottom and thus does not reproduce the zones of sediment deposition observed experimentally. The ‘Van Rijn BTKE’ condition strongly underestimates the sediment deposition, or limits it to only a few particles for high discharges. The sediment deposits obtained with the ‘Brownlie BSS’ condition reproduce the zones of sediment deposition observed for the lowest discharge particularly well. On the other hand, for the other two discharges, a large number of particles were deposited in zones that should be free of any sediment. Lastly, the sediment deposits obtained with the ‘extended Van Rijn BTKE’ condition are in good agreement with the observations of Stovin & Saul (1994). The zones free of sediment for the low discharge are fairly well reproduced, despite a slight overestimation of the size of the longitudinal strip free of sediment along the main jet. For the intermediate discharge, the sediment deposits in the upstream left and right corners are clearly shown. The isolated deposit in the centre of the basin is, however, averagely reproduced. For the highest discharge, the model reproduces the sediment depositions in the upstream left and right corners, with the rest of the structure remaining free of sediment.
The experiments of Dufresne et al. (2009)
The comparison of the numerical and experimental results can be found in Isenmann (2016), only conclusions are presented here.
Whatever the condition of interaction between the particles and the walls, the trapping efficiencies calculated by the model are overestimated in comparison with the experimental measurements. It should be noted however that the relatively high uncertainty on the density of the particles in comparison to that of water (1,034 ± 19 kg/m3) makes the trapping efficiencies calculated very sensitive. In view of this observation, it seems more advisable to use the sediment deposits in the structure as the basis for evaluating the pertinence of the conditions of interaction at the wall. Although the BTKE condition using a fixed value of ξ equal to 1 appears the most pertinent regarding the trapping efficiencies calculated, it nonetheless leads to a poor representation of sediment deposits for most of the experiments (considerable underestimation of the zones of sediment deposition). This condition is therefore unsatisfactory, as it permits reproducing trapping efficiency at the expense of reproducing sediment deposition well. Finally, in spite of the trapping efficiencies calculated that are globally higher than the experimental measurements, the ‘Van Rijn BTKE’ condition (in this case equivalent to the ‘extended Van Rijn BTKE’ condition) appears the most pertinent. The preferential zones of sediment deposition are well-reproduced for all the experiments and the trapping efficiencies calculated with densities of 1,015 kg/m3 and 1,025 kg/m3 are fairly consistent with the experimental trapping efficiencies, though without considerably degrading the representation of the zones of sediment deposition.
Discussion of trapping efficiency and zones of sediment deposition
The model developed was applied to three series of experiments performed on scale models of basins with a view to verifying the model's capacity to reproduce the phenomena involved in sediment transport in a settling basin. The two essential data for validating the model were the particle trapping efficiency of the structure and the preferential zones of sediment deposition on the bottom.
The model's capacity to reproduce the efficiency of a structure was first verified by comparison with the experimental data of Frey et al. (1993). For the 34 experiments covering dimensionless diameters d* between 0.5 and 5, the mean variance between the trapping efficiencies calculated and measured was about 6%, as most of the values were inside the experimental error bars. Given the hydrodynamic conditions and the properties of the particles, the sediment depositions could occur over the whole bottom of the basin. Therefore the impact of the new interaction conditions regarding the preferential zones of sediment deposition was not studied for these experiments, since most of them provided the same results as those obtained with the stick condition (the two BTKE conditions using a fixed value ξ led to results inconsistent with the experimental observations, thereby demonstrating their limits).
On the contrary, the stick condition was poorly adapted in the case where zones free of sediment occurred on the bottom of the structure, such as in the experiments of Stovin & Saul (1994) and Dufresne et al. (2009). The new interaction conditions implemented were therefore studied using these two sets of experimental data. Initially, the range of d* between 0.1 and 2.5 (d*50 = 0.77) was investigated on the basis of the experiments of Stovin & Saul (1994). The ‘extended Van Rijn BTKE’ condition provided satisfactory results, both for the trapping efficiencies and for the preferential zones of sediment deposition on the bottom. The other BTKE conditions, i.e. the ‘Van Rijn BTKE’ condition and the two BTKE conditions using a fixed value ξ (1 or 5), demonstrated their inability to reproduce the measurements and experimental observations for the range of d* investigated. The condition based on thresholding the shear stress (Brownlie BSS) permitted the acquisition of acceptable trapping efficiencies although it proved limited for reproducing zones of sediment deposition for strong discharges. Secondly, the range of d* between 2.5 and 10 (d*50 ≈ 5) was studied using the experimental data of Dufresne et al. (2009). Once again, the ‘extended Van Rijn BTKE’ condition (equivalent to ‘Van Rijn BTKE’ for this range of d*) gave the most satisfactory results. The two BTKE conditions using a fixed value ξ (1 or 5) proved to be incapable of faithfully reproducing the zones of sediment deposition on the bottom, which were either underestimated (ξ = 1) or overestimated (ξ = 5). The zones of sediment deposition obtained with the ‘Brownlie BSS’ condition were poorly reproduced, especially for deep water depths in the basin.
Finally, the ‘extended Van Rijn BTKE’ interaction condition proved to be the most pertinent for d* between 0.1 and 10. Generally, it permitted the satisfactory reproduction of the particle trapping efficiencies and zones of sediment deposition for the three series of experiments on the scale models of basins.
CONCLUSIONS AND OUTLOOK
The objective of this study was to develop a tool for evaluating the performance of a settling basin in terms of trapping SM (efficiency of the structure). A numerical method using the Euler-Lagrange method was chosen to model flow and sediment transport. A solver for Lagrangian modelling was formulated using the library OpenFOAM®. It was developed for free surface flows, since it utilises the hydrodynamic results of a multiphase solver using a Volume of Fluid method.
New conditions of interaction between particles and walls, of BSS and BTKE type, were proposed to determine the threshold values at the scale of the particle. In particular, a new relation was presented to calculate the turbulent kinetic energy threshold as a function of the properties of the particle (diameter and density). This relation was based on the evaluation of kc = ξ·ws2 with ξ calculated on the basis of (extended) Van Rijn criteria (1984b) as a function of d*; and ws calculated by a balance of forces acting on the particle.
The numerical model was applied to three series of experiments performed on scale models of basins (Frey et al. 1993; Stovin & Saul 1994; Dufresne et al. 2009) to verify the capacity of the model to reproduce the phenomena involved in sediment transport in a settling basin. The results obtained with the new ‘extended Van Rijn BTKE condition’ proved satisfactory for the particle trapping efficiency and for the preferential zones of sediment deposition. Indeed, the model reproduced efficiency with an absolute error in the region of 5% in the case of sediment deposits on the whole bottom. In the case of localised sediment deposits, preferential zones were faithfully reproduced and the efficiency was evaluated with an absolute error in the region of 10% (except for particles of very low density).
Finally, a numerical tool is available and validated to evaluate the performances of a settling basin regarding its efficiency for trapping SM. This tool is currently applied in the framework of the SIMPLUV project, one of whose objectives is to develop a prefabricated settling structure. The tool is used to test different shapes and configurations of structure with a view to maximising the amount of material deposited. An experimental phase on a physical model of the settling basin at real scale will reinforce the developments carried out by the numerical tool and lead to validating the model on a real structure (without similitude). The scope of application of the tool is intended to be wider than in the SIMPLUV project. For example, it could be used in the design phase or for the renovation of a larger basin (in the region of several thousand cubic metres) to propose shapes and configurations designed to maximise the trapping of SM or reduce its volume for a given level of performance.
More generally, the scientific outlook for this work is the following. From the numerical standpoint, it will be interesting to proceed with a more in-depth study of the spatial distribution of the sediment deposits. The qualitative comparison (visual) could be completed by a quantitative analysis via, for example, the surface density or another parameter representative of the thickness of the sediment deposit. From the experimental standpoint, this will require performing measurements that will permit building a database of experimental data on the heights of sediments on the bottoms of basins. Work using this type of measurement, based on an ultrasonic method, started during the experimental campaign of the SIMPLUV project (Isenmann 2016).